新闻中心 / NEWS
行业新闻
当前位置:网站首页 > 新闻中心 > 行业新闻
  • 塑料托盘合理利用库场平面,进行集货、配货分析
  • 本站编辑:杭州宏展塑料有限公司发布日期:2019-07-29 18:30 浏览次数:

塑料托盘合理利用库场平面,进行集货、配货分析,提高计算机的的管理效率。现分析物资储存管理业务流程中的关键技术,以便对集货管理的数据浇定义。建立储存率场的布置标签,对建筑物、库房、区域等编有永久工程图纸号码的仓库,为了表明物资的储存位置,给这类设施编上号码。 塑料托盘厂家建立每个库场或室外储存场地的实际地面布置平面图,显示出库房或室外储存场地的总面积的具体划分。所划分地区可用作储存区、发货区和接收区,作业通道存表室或休息室及办公室。其中储存区可进一步划分为散装物资储存区,小批量物资储存区,中批量物资储存区等。沿着各货柜方格的周边线从下至上、从左至右的顺序标明数字。如果需要每一区、每一库房分区均按从左至右的顺序重新标识,其纵、横格的标识在所有储存区均应一致。塑料托盘各个类似的库场或室外储存场地,同一编号的方格均应处于相同的位置尚未储存物资的方格搜有必要标明编号,予以保留以便在储存变更时加以利用。为丁保证物资增多时的运输畅通。在平面图上应将用作通道的方格编号标出。注明作为通道使用,以便计算机进行现场运输模拟,防止在物资运输过程中出现拥挤、阻塞现象同时一旦帮要改变储存位置,新的布置所需要的方格就是现成的,也不会打乱原来的编号。除了上述的储存位置标志外,塑料托盘垂直储存位置也需要有标志。货柜架、托盘货架或类似的储存设备的各个货格,都需要此类标志。为了便于运输调度,还应将每十库场或室外储存场地的各类停车车位予以标记。建立物资到、停、卸、运、储的计算机数据库模型。 确定物资储存的原则相同的物资尽能储存在一起,周转快的物资应储存在能便于接近的区域,塑料托盘以缩短物资装卸搬运设备和物资提取人员的工作距离。货柜物资和零散物资收发区应该设在包装和作业区附近。塑料托盘不仅影响储存场地的数量分配,而且还影响储存物资的位置。储存大型或重型的物资的地区,应尽可能靠近包装、接收或发货区,少装卸搬运费用。

The plastic pallets make reasonable use of the storage area plane to collect and distribute goods and improve the management efficiency of the computer. This paper analyzes the key technologies in the business process of material storage management in order to define the data of goods collection management. Establish layout labels for storage sites, number warehouses with permanent engineering drawings for buildings, warehouses, areas, etc., and number such facilities to indicate where supplies are stored. The plastic tray manufacturer establishes the actual floor plan for each warehouse or outdoor storage site showing the specific division of the total area of the warehouse or outdoor storage site. The divided area can be used as storage area, delivery area and receiving area, operation channel storage room or lounge and office. The storage area can be further divided into bulk material storage area, small batch material storage area, medium batch material storage area and so on. Indicate Numbers along the perimeter lines of each container grid from bottom to top, left to right. If it is necessary to re-mark each area and each warehouse partition from left to right, the vertical and horizontal marks shall be the same in all storage areas. For similar storage sites or outdoor storage sites of plastic trays, the grid with the same number shall be in the same position. If there is no material stored in the grid, it is necessary to mark the number and keep it for use when storage changes. To ensure the smooth transportation of more materials. The grid Numbers used as channels should be marked on the plan. Note as a channel to facilitate the computer to carry out field transport simulation, to prevent congestion, blocking phenomenon in the process of material transport at the same time, once help to change the storage location, the new layout required by the grid is readily available, will not disrupt the original number. In addition to the above storage location mark, the plastic tray vertical storage location also needs to be marked. Such marks are required for the shelves of containers, pallets or similar storage equipment. In order to facilitate transportation scheduling, also should be every ten storage yard or outdoor storage site of all kinds of parking Spaces to be marked. Establish the computer database model of material to, stop, discharge, transport and storage. The same materials can be stored together, fast moving materials should be stored in an accessible area, plastic trays to shorten the working distance between the material handling equipment and the material extraction personnel. Container supplies and scattered supplies shall be located near the packaging and operation area. Plastic trays not only affect the quantity distribution of storage sites, but also affect the location of storage materials. The area where large or heavy materials are stored should be as close as possible to the area where they are packed, received or shipped, so as to reduce handling costs.